For Sale One of a kind Moxie Mike Chip Tray! (1 Viewer)

This a piece Moxie Mike built for me. It has a red oak stain and is very well constructed. Leather rope handles on the side and the foam inside is machined to fit around 480+ chips, plaques, dealer buttons, and jettons of varying sizes 45mm, 53mm etc. If you were in the MSK jeton group buy you can see from the pictures below how the various items fit. This also had a lid to go over the top. I paid over $300 for this bad boy shipped. It is a beautiful piece and has basically not been used. I planned on using it as transportation vessel but sadly I'm the major host in my group lol. If I had space in my man cave I would load it up and display it but I do not have any spare room to for it to sit out on display. You will also get a second piece of tempered glass as a backup. Shipping to CONUS only at cost.

$220 + shipping.
Now to the pr0n!

 

[sheikh617]

Foam is also replaceable. You can build your own configuration online and swap as needed.

 

[Moxie Mike]

Foam is also replaceable. You can build your own configuration online and swap as needed.

I can provide the dimensions and product specs to whoever picks this up.

 

[sheikh617]

Bump

 

[EnjoyLife]

Beautiful looking case. GLWS

 

[Charly]

Oh yess !!!

 

[horseshoez]

Very tempting. Would the replacement foam just be ordered from @Moxie Mike if the buyer wants a new config? If so, cost of doing it?

 

[Moxie Mike]

Very tempting. Would the replacement foam just be ordered from @Moxie Mike if the buyer wants a new config? If so, cost of doing it?

I don't sell the foam. The foam comes from a company in NJ called mycasebuilder.com. it costs about $50 landed for that size case.

They have a design tool on their site... So you design your configuration and place the order. I'll gladly provide all the specs and help you design a different foam piece if you want.

 

[horseshoez]

I don't sell the foam. The foam comes from a company in NJ called mycasebuilder.com. it costs about $50 landed for that size case.

They have a design tool on their site... So you design your configuration and place the order. I'll gladly provide all the specs and help you design a different foam piece if you want.

Nice, thanks for the info Mike. Didn't know it was from them actually. I've seen their work for Pelicans and it's really impressive. Nice to know they made this one too. Also had no idea you could play around with the colors. Going to check on the size of the set I would be using and see if I'm going to go for it or not. Also envisioning a LED strip on the underside of the cover. That would just look badass!

 

[sheikh617]

Nice, thanks for the info Mike. Didn't know it was from them actually. I've seen their work for Pelicans and it's really impressive. Nice to know they made this one too. Also had no idea you could play around with the colors. Going to check on the size of the set I would be using and see if I'm going to go for it or not. Also envisioning a LED strip on the underside of the cover. That would just look badass!

Sure would. Could make for a nice display piece or you can use it as a sweet travel case. Shoot me a PM if interated or you have any questions.

 

[horseshoez]

Sure would. Could make for a nice display piece or you can use it as a sweet travel case. Shoot me a PM if interated or you have any questions.

Definitely will Moe. It's had my attention ever since you showed it to us after receiving it.

 

[sheikh617]

For sure. It's a beauty. I literally have it in a closet for space reasons and it saddens me deeply lol.

 

[sheikh617]

Bump!

 

[sheikh617]

Bump

 

[sheikh617]

bump!

 

[warewulf]

Wow, that's so nice, nice job @Moxie Mike !

@Suited Connector

 

[TeamNapoli]

would you know if you just used paulson chips say 66.7 cut outs, how many chips the display can hold? Also is the foam strong enough to maintain the chips in place if the display was vertical on a wall?

 

[sheikh617]

would you know if you just used paulson chips say 66.7 cut outs, how many chips the display can hold? Also is the foam strong enough to maintain the chips in place if the display was vertical on a wall?

If you did an all chip cut out I'd say 600-700 chips and I would not do full vertical. The best way to use it as display would be to mount it on something that puts it at an angle.

 

[TeamNapoli]

is the issue for not full vertical due to the foam is there a different foam i could use? i was thinking about a flush mount wall display ie a poker chip medicine cabinet.

 

[sheikh617]

is the issue for not full vertical due to the foam is there a different foam i could use? i was thinking about a flush mount wall display ie a poker chip medicine cabinet.

Personally, I don't think that will be a great application for this case. The foam holds the chips snug enough where if they are mint Paulsons, they won't fall out when vertical, but the chip tray itself is heavy and the lid isn't hinged.

 

[TeamNapoli]

ah ok, thanks for the feedback

 

[Moxie Mike]

is the issue for not full vertical due to the foam is there a different foam i could use? i was thinking about a flush mount wall display ie a poker chip medicine cabinet.

That wouldn't be a proper use for this particular case. Foam also wouldn't be a good choice for a vertical storage box - horizontal dividers with a hinged front (like traditional cabinet doors) would be far more appropriate. You'd be better off with something you can stack acrylics racks in.

 

[TeamNapoli]

not for the way i desire to display the chips, but thanks for the advice

 

[sheikh617]

Bump!

 

[sheikh617]

Forgot about this. 2 month later bump

 

[Moxie Mike]

GLWS (again!)

 

[sheikh617]

@Organista1

 

[Organista1]

@Organista1

no thank you that’s not what I’m looking for

 

[sheikh617]

Bump. Great looking piece for chip storage. You could even pull the foam out and and load it with racks of chips.