Oiling Chips Done Right (8 Viewers)

[DMack]

Reds ALWAYS pop with a touch of oil. So good!

View attachment 1287813

You’re so right about red.

 

[BigDutch888]

Just did two racks with this method, looks great and very easy to do!

 

[YepImNaked]

Using the method in the original post on my Paulson casino chips. Just wiping off the inlays and racking them up after they’ve air dried for 48 hours. I have some un-oiled control chips I can photograph them next to later. Should be interesting to see how it holds up after a month or two

 

[Frnkbonz]

I like this method. I neglected a set of chips for years due to non use. Definitely has that chalky color to them. I will show before after.

 

[ichorus728]

I have a fresh set of CPC rounders on the way. Wondering if I should oil the new chips.

 

[Colquhoun]

I have a fresh set of CPC rounders on the way. Wondering if I should oil the new chips.

When you get them, they’ll be dusty and the edges will look a bit faded. A few drops of oil on a cloth, wipe just the edges of 10-20 stacked chips at a time, then wipe off with a dry cloth. No need to oil the faces, just wipe them off with the dry cloth as well.

 

[krafticus]

When you get them, they’ll be dusty and the edges will look a bit faded. A few drops of oil on a cloth, wipe just the edges of 10-20 stacked chips at a time, then wipe off with a dry cloth. No need to oil the faces, just wipe them off with the dry cloth as well.

 

[TX_Golf_N_Poker]

When you get them, they’ll be dusty and the edges will look a bit faded. A few drops of oil on a cloth, wipe just the edges of 10-20 stacked chips at a time, then wipe off with a dry cloth. No need to oil the faces, just wipe them off with the dry cloth as well.

Is there a specific reason not to put any oil on the faces of new CPCs?

For those of you who have CPC chips, did you just oil the barrel edges straight away? Or did you rinse off the chips (to get as much chip dust off as possible) prior to oiling? I've seen people swear by both ways.

I oiled one barrel of each denomination (without a water rinse) to see how it would hold up, and after 4 days they still look great. So I'm wondering if the rinse step is necessary.

View attachment 1138809

Does any of this "dustiness" on the edges carry over onto the faces? I would think at least the outer rim where the mold is would benefit from a touch of oil.

 

[Himewad]

Does any of this "dustiness" on the edges carry over onto the faces? I would think at least the outer rim where the mold is would benefit from a touch of oil.

Yes, it definitely does carry over onto the faces. I did a quick wipe on the outer rim on my chips. But didn't oil nearly as heavily as I did on my china clays.

 

[Colquhoun]

Is there a specific reason not to put any oil on the faces of new CPCs?


Does any of this "dustiness" on the edges carry over onto the faces? I would think at least the outer rim where the mold is would benefit from a touch of oil.

I'm not a fan of really oily chips, and frankly the faces dont really need it. However, the edges after grinding are very dusty and dry, so th oil really helps there.

 

[Poker Zombie]

I oiled the faces as well. However, most the oil went to the outside, as I would do a barrel's outside then did the faces with the same cloth (no extra oil).

I'm pretty sure I posted this before, but it's worth the repost.

It goes faster if you use 2 hands, but I needed to hold the camera.

I haven't needed to re-oil any clay chips since the first oiling, so you just get the China clay version. Sit at a table, put on a 30 minute video or sitcom and knock out 3 racks. One college lecture and you can finish a tournament set.

 

[Lunettesman]

My chips hadn't seen a brush or oil for ages as I don't use them so much. I did your technic. In the process of drying. After the first 48h when you stack them in 10 I made a slight change. I stack them in 20 in the middle of a rack and apply a second coating that way. I can pressure the chips very well and slightly rotated the all 20 in a move. I have one rack dedicated for that. In a similar fashion when I have cleaned them up, I finish with stacks of 20 in the middle of a rack and then brush intensively just the edges. Works magic.

 

[Lunettesman]

Day and night

 

[fumblingwisdom]

This is super cool, and something I never would have thought to do on my own. Looking forward to trying it out

 

[drdr]

Does any of this "dustiness" on the edges carry over onto the faces? I would think at least the outer rim where the mold is would benefit from a touch of oil.

I found it depends on the colour of the chip. Some colours didn't need or benefit from oil on faces, but others needed oil so faces matched edges in 'pop'.