Sold Fire Sale 3d printing and misc items, 2nds, defects and incomplete projects (1 Viewer)

[Sparkynutz]

Auction Details (Archived)

---

Auction ends at: 9:00 PM Eastern Time
Auction ends on: Sep 29, 2024
Starting bid: $5
Minimum bid increment: $5
Payments accepted: PayPal F&F, PayPal G&S, Venmo
Shipping terms: OTHER (see below)
Ships via: USPS Priority

---

Declutter project

Selling all 3d printed first runs, defects, 2nds, incomplete projects.

***No guarantees that any of these items are compatible with currently offered production products or items they were designed for***

Also included is a few used racks, 2 sets of BA #4 defect cards. An off center dealer button, and a few other misc items.

This is an all or none auction. All items shipped in one large box. USPS ground advantage (not listed as an auction option) or priority.
Buyer pays actual shipping cost and insurance if desired.

The only acception is an incomplete birdcage project my dad started that can be included with or without the rest auction due to shipping cost. Free local pickup or meetup near zipcode 53963 Wisconsin.

 

[demonnic]

$5 I'll happily start this off

 

[Flopalopagus]

25

 

[Flopalopagus]

Happy to support as well. . No gimme gimme.

 

[Flopalopagus]

^Now gimme gimme.

 

[demonnic]

30 weeee

 

[Sparkynutz]

Found a few more first run items to add to pile. 41mm stacker set and a couple card holders that fit snug

 

[Sparkynutz]

Bump

 

[Sparkynutz]

12 hours left

More details on products-

The E racks especially will make this lot a pretty big discount at current bid amount.
Most have only a very minimal visual defect on bottom of tray that's covered by chips or top finish is different pattern than my current production. Most if not all fit chips and interlock well.

Shuffle stacks, are similar with either very minimal visual defects or no defects but fit tight so they will work great for worn chips.

2 of the Stacker sets are fully fuctional, just have poor top finish.

The 41mm blue set fits too snug but would work for 40.5mm chips perfectly.

There's enough 80mm dealer button inserts to make a handful of racks. I printed too many extras with each new batch at the start and didn't feel like sorting them by size and print finish to match.
Painting the boxes didn't go as well as planned. Sand and paint them better, Add some spacers with the inserts in this lot and you'll save a couple hundred bucks right there.

There's a few 65mm inserts printed as extras with each batch. Probably just fine for making a small rack.

Card trays- Cards fit snug in one, Dealer button fits snug in the other.

Mitsui racks I see selling around $4 each.
1 has a very tiny crack, rest look used but good.

All game plaques have a minor finish issue or string in wrong place.

Mitsui plaque rack 60mm db inserts have minor print defect glob in one spot. Visual issue only.

Hope this additional info help anyone interested in bidding.

 

[Bacon Dad]

35

 

[WedgeRock]

40

 

[WedgeRock]

Snipe it if you want it, @Bacon Dad.

 

[Bacon Dad]

That’s ok. I’m all set now.

 

[Bacon Dad]

Only wanted to spend. $30 but was forced to 35. Don’t want to do 45.

 

[Sparkynutz]

Or see who wants what and split it?

 

[Sparkynutz]

I just noticed the auction says Eastern time not my time zone...
Central.
I didn't realize this was already done.

 

[Bacon Dad]

If @WedgeRock wants to split stuff up, I’ll spend $20 + shipping if it’s a for split.