$1 Indiana Grand Chips for Sale (5 Viewers)

[Apache]

These chips are in good condition but all of them have pink stains. It is hard to remove the stains. I have them for sale for $49 per rack.
https://www.apachepokerchips.com/product/rack-of-indiana-grand-casino-1-paulson-poker-chips/

 

[shorticus]

How many racks available?

 

[Apache]

I have over 1000 left.

 

[Bacon Dad]

What are the stains from?

 

[MarCobi]

I have over 1000 left.

1000 racks or chips?

 

[improviseallday]

Halloween limit set?

 

[Apache]

One thousand chips. I am not sure how they chips got stained.

 

[BigSlick4523]

1000 racks or chips?

I am sure he means 10 racks meaning 1,000 chips

 

[bergs]

The chips are faint red from the departed souls of dying 2-4 limit holdem and 1-5 spread stud hi only players.

 

[Bacon Dad]

And now I know.........

.........the rest of the story.

 

[inapinch]

What are the stains from?

I imagine it’s like a dog scooting across the floor, except it’s chips

 

[Bacon Dad]

Now that's a visual I didn't need to associate with my chips.

 

[FoldingAces]

Nice, just scooped up 2 racks! I'll give them a good clean when I get them and post a picture on this thread if its still up.

 

[qiu_lijie]

Nice, just scooped up 2 racks! I'll give them a good clean when I get them and post a picture on this thread if its still up.

Also caved and ordered a few racks, but instead of cleaning them I have the thought of leaning into the fact they are a bit pink to begin with. Perhaps dyeing more pink and relabeling them to become fracs would be an idea. They are inexpensive enough to experiment with anyways

So I saw a few posts about dyeing chips on the forums here already, anyone have a more comprehensive guide for that as well as murder/relabeling?

 

[Colquhoun]

Also caved and ordered a few racks, but instead of cleaning them I have the thought of leaning into the fact they are a bit pink to begin with. Perhaps dyeing more pink and relabeling them to become fracs would be an idea. They are inexpensive enough to experiment with anyways

So I saw a few posts about dyeing chips on the forums here already, anyone have a more comprehensive guide for that as well as murder/relabeling?

I would give them a soak for 10-15 minutes in Oxy-clean with warm water to try and get them whiter…before resorting to try and dye them pink.
The used primary HSI $1 chips I had were yellowed slightly and I had to do 2 or 3 soaks in Oxy-clean, but they got MUCH whiter. A little mineral oil brought back the color to the edgespots that inevitably fade when exposed to Oxy-clean.

 

[qiu_lijie]

I would give them a soak for 10-15 minutes in Oxy-clean with warm water to try and get them whiter…before resorting to try and dye them pink.
The used primary HSI $1 chips I had were yellowed slightly and I had to do 2 or 3 soaks in Oxy-clean, but they got MUCH whiter. A little mineral oil brought back the color to the edgespots that inevitably fade when exposed to Oxy-clean.

I won't say resorting to doing so, as my intention is to make pink-ish fracs out of them. I think clay being quite porous, a water based paint/dye should do the trick

 

[Colquhoun]

I won't say resorting to doing so, as my intention is to make pink-ish fracs out of them. I think clay being quite porous, a water based paint/dye should do the trick

A while back, another member tried staining them…but the result was that the stain does not penetrate much, if at all:
https://www.pokerchipforum.com/threads/wood-stained-chip-science-project.73456/

 

[qiu_lijie]

A while back, another member tried staining them…but the result was that the stain does not penetrate much, if at all:
https://www.pokerchipforum.com/threads/wood-stained-chip-science-project.73456/

Thanks for the tip. I started a thread in the custom chip section looking for more info. Yeah so far staining/dyeing doesn't seem to be recommended. Perhaps air brush is also an idea. I also saw a post where someone used a sharpie with okay result https://www.pokerchipforum.com/threads/dying-poker-chips.8040/

Edit: looking at that stained chip again, it is not even that bad either

 

[ekricket]

I would give them a soak for 10-15 minutes in Oxy-clean with warm water to try and get them whiter…before resorting to try and dye them pink.
The used primary HSI $1 chips I had were yellowed slightly and I had to do 2 or 3 soaks in Oxy-clean, but they got MUCH whiter. A little mineral oil brought back the color to the edgespots that inevitably fade when exposed to Oxy-clean.

I think the acidic route, vinegar and salt for example, or a weak muriatic acid, or maybe even lemon juice might be better than the oxidizer. Some of the other stains on chips seem to be more from oxidation and therefore a reduction might be better.

 

[RedDirtBo]

My rack was delivered today. The staining wasn't bad in my opinion, but I can see someone more OCD than I am being triggered. The dirt/hooker juice on the sides bothered me more, but oxyclean, and a sonic scrubber took care of that. Well worth the price!

 

[BigSlick4523]

My rack was delivered today. The staining wasn't bad in my opinion, but I can see someone more OCD than I am being triggered. The dirt/hooker juice on the sides bothered me more, but oxyclean, and a sonic scrubber took care of that. Well worth the price!

Pics ? And I assume you are talking about a UltraSonic lol

 

[TheOffalo]

Pics ? And I assume you are talking about a UltraSonic lol

Could be talking about a battery-powered brush:

 

[criesen]

Pics ? And I assume you are talking about a UltraSonic lol

Would appreciate some pics too.

 

[FoldingAces]

Received my racks in the mail yesterday. Packaging on point!! Very impress. The stain wasn’t that bad, will post a pic when I’m home later. About 11 hours from the time of this post. If you’re in the border of getting a rack, do it.

 

[benjaminbreakfast]

Murdering in progress.

 

[FoldingAces]

Murdering in progress.
View attachment 1225739

What is the replacement? Gear inlays?

 

[Manjankins]

Put me down for 3 racks

 

[Manjankins]

I didn’t see the pink. Scratch that.

 

[benjaminbreakfast]

What is the replacement? Gear inlays?

Oh ya!!!
Got @mattross1313 working on the inlay now.
Hopefully im done with all the murder when they get here from @Gear

 

[FoldingAces]

Oh ya!!!
Got @mattross1313 working on the inlay now.
Hopefully im done with all the murder when they get here from @Gear

Nice, I plan on doing the same eventually. Gonna make this part of a cash set.