New Paulson Chip Rack Supplier (3 Viewers)

The 43mm Chipco racks fit 43mm Paulsons like a glove but as @BGinGA said their 39mm racks are a tad looser.
I'm confused about the size racks I need for regular, casino Paulsons.....66.7mm, 43mm, 39mm??? I think I need 66.7mm, but what are the smaller racks for? The chips I am buying these for fit perfectly into the Paulson CHIP24010 racks...are those 66.7mm?
 
I'm confused about the size racks I need for regular, casino Paulsons.....66.7mm, 43mm, 39mm??? I think I need 66.7mm, but what are the smaller racks for? The chips I am buying these for fit perfectly into the Paulson CHIP24010 racks...are those 66.7mm?

I think you're getting a little mixed up here. 66.7mm refers to the length of the rack. 20 Paulsons will fit very snugly in a 66.7mm rack. The 43mm and 39mm refer to common chip diameters, and therefore the width of the molded depression that the chips sit in, not the length.
 
I think you're getting a little mixed up here. 66.7mm refers to the length of the rack. 20 Paulsons will fit very snugly in a 66.7mm rack. The 43mm and 39mm refer to common chip diameters, and therefore the width of the molded depression that the chips sit in, not the length.
Thank you!
 
I finally got around to ordering some of the 4200s last week. The shipping cost is definitely painful.

These just arrived today and are fantastic! Having never possessed proper chip racks for my Paulson chips the pain of the associated shipping costs was definitely worth it. I ordered several cheaper racks from various sources and none of them provided the fit I was looking for. If you are looking for racks for your Paulson chips I would say definitely do not waste your time or money on anything else and just buy these.

Thanks for this amazing find.
 
Best to buy when visiting Las Vegas , next time I go to Vegas im def picking up more racks and a birdcage that I can hand carry on plane to avoid all the shipping

Is there an actual B&M storefront you can go to to buy the racks, or would you just coordinate an in person pick up?
 
Is there an actual B&M storefront you can go to to buy the racks, or would you just coordinate an in person pick up?

Others that are in Vegas can correct me if I'm wrong, but I don't think there is a storefront. More than likely you would have to call ahead of time, place your order and pick them up. Here is a shot of the building.

uniqueb&M.jpg
 
Is there an actual B&M storefront you can go to to buy the racks, or would you just coordinate an in person pick up?
If you are going to Vegas, and are looking for chip supplies, you must check out Spinettis.

Not only are they a PCF vendor, but they are a solid brick and mortar store. When I need racks for hard-to-fit chips, I bring a barrel and go through the selections until I find a rack that the barrel fits. Only downside is that you may find a bunch of other things that you didn't know you needed until you see them.
 
If you are going to Vegas, and are looking for chip supplies, you must check out Spinettis.

Not only are they a PCF vendor, but they are a solid brick and mortar store. When I need racks for hard-to-fit chips, I bring a barrel and go through the selections until I find a rack that the barrel fits. Only downside is that you may find a bunch of other things that you didn't know you needed until you see them.
@Spinettis Gaming store is awesome!

I did go in there...without a shopping list...but managed to find things to buy.... It's a bit dangerous.
 
Hi guys, what was the cost you got for the 24010 racks? What were the price breaks ? Maybe a group buy would be in order? I have tried calling Paulson, GPI and now angel but no replies.. I’ll try again tomorrow...I honk we could send a sample tomchina and get them make there. Also standard chips are 39mm. I am thinking of making a slightly larger rack or two. Something like a 41mm and a 43mm rack to handle the larger higher denom chips.. your 8nfo and thoughts?
 
Hi guys, what was the cost you got for the 24010 racks? What were the price breaks ? Maybe a group buy would be in order? I have tried calling Paulson, GPI and now angel but no replies.. I’ll try again tomorrow...I honk we could send a sample tomchina and get them make there. Also standard chips are 39mm. I am thinking of making a slightly larger rack or two. Something like a 41mm and a 43mm rack to handle the larger higher denom chips.. your 8nfo and thoughts?
Nobody better dare dash this members dreams about getting stuff directly from GPI. Let him keep his innocence or else I’ll fight you!

Keep calling, keep trying! Worst they can say is no and if somehow they say yes, let us know!!!
 
Still trying to get a real person.. probably nothing will come of it, but it’s only a 5 minute call.. so I go and could my 800 CDI 98’s after... hehehehehehehe
 
How are those racks? I have some cheap p.o.s. Racks but the people in Vegas have the original Paul-son mold racks, those work well but are expensive. I’ll check into the other racks u guys are talking about. Thanks for the info..


Btw. Any one looking for CDI- 98 chips? I have some to get rid of..
 
How are those racks? I have some cheap p.o.s. Racks but the people in Vegas have the original Paul-son mold racks, those work well but are expensive. I’ll check into the other racks u guys are talking about. Thanks for the info..


Btw. Any one looking for CDI- 98 chips? I have some to get rid of..
Yes what denoms?
 

Create an account or login to comment

You must be a member in order to leave a comment

Create account

Create an account and join our community. It's easy!

Log in

Already have an account? Log in here.

Back
Top Bottom